以下是 滑模机的详细介绍页面，由于豫信致诚机械设备(红河市分公司) 滑模机产品种类较多，具体 滑模机产品价格请致电，以电话中实际报价为准。
软管泵可应用于多用移动泵站的结构 :自吸高度可达到9米，水平自吸可达200米以上，无需灌泵。特别适合于市政下水道系统的污水、污泥抽排。无堵塞、杂质通过能力强。普通的塑料袋、沙石、编织袋、泥浆、毛发等杂物都不会影响泵的使用。采用原轮泵，耐干运行，泵体坚固耐用、寿命长。使用快速连接接头，方便进出口管道的装配。 整车设计紧凑、适应于狭小空间使用。使用便捷拆卸式防雨布、或硬质钢板隔音罩，低噪音设计，符合环保标准要求。
The hose pump can be applied to the structure of a multi-purpose mobile pumping station: self-priming height can reach 9 meters, horizontal self-priming can reach more than 200 meters, no need for drainage irrigation pump. Particularly suitable for sewage and sludge drainage in municipal sewer systems. No blocking, strong ability to pass impurities. General plastic bags, sand, woven bags, mud, hair and other sundries will not affect the use of the pump. The original wheel pump is resistant to dry running, and the pump body is durable and durable. Use quick connect joints to facilitate the assembly of inlet and outlet pipes. The complete vehicle design is compact and suitable for use in small spaces. Easy-to-remove rainproof cloth or hard steel sound insulation cover, low noise design, meet environmental protection standards.
工业软管泵不锈钢齿轮泵，可输送非润滑油饮料低腐蚀性液体，配铜齿轮可输送汽油苯等低内点液体。由于齿轮泵自吸能力差，一般是由于齿轮泵泵腔间隙较大所致。同时也是如果齿轮泵输出端没有“止回阀”，则必须是下一级齿轮泵的止回阀或控制阀。移动固定后，周围工作人员可恢复手术。
Industrial hose pump stainless steel gear pump, can transport non-lubricant beverages with low corrosive liquids, with copper gears can transport gasoline, benzene and other low internal point liquids. Due to the poor self-priming ability of the gear pump, it is generally caused by the large gap between the pump cavity of the gear pump. At the same time, if there is no "check valve" at the output of the gear pump, it must be a check valve or control valve of the next gear pump. After moving and fixing, the surrounding staff can resume surgery.
泵出厂时，压辊已按正常情况调整到位，如遇物料吸不上，或在泵的额定压力下，口量达不到要求，请调整压辊的偏心距，其步骤如下：
（1）先将泵壳两侧相应的圆孔有机玻璃盖板与泵出口端的长方形有机玻璃盖板打开，将转子压辊旋转至两圆孔之间，其螺栓正对圆孔，然后用套筒扳手将两端螺栓拧松，再用小圆棒或十字螺丝刀，对准标有0，1，2，3的圆孔，拨动压辊一侧内的偏心套转动，偏心套的数字越大，其压辊与泵壳间的距离越小，软管压的越紧，其调整是以转子的顶端的刻线为基准，数字越大，压的越紧，反之亦然。
（2）调整间隙时一定要注意不要压的过紧，以达到流量为准，压的越紧，对胶管的寿命影响越大。
软管泵属于蠕动泵的范畴，主要是由一根特制的橡胶软管，对应泵体内转子总成上的一对压辊，当压辊沿着橡胶软管转动时，压辊与泵壳产生的挤压力将橡胶软管压扁，在软管自身弹性和侧导辊的强制下，通过恢复原状产生的真空吸入流体物料，物料在压辊的机械挤压下从管内排出，如此往复循环，从而达到连续输出物料的目的。
The hose pump belongs to the category of peristaltic pump. It is mainly composed of a special rubber hose corresponding to a pair of pressure rollers on the rotor assembly in the pump body. When the pressure roller rotates along the rubber hose, the pressure roller and the pump housing The squeezing force flattens the rubber hose. Under the elasticity of the hose itself and the force of the side guide rollers, the fluid material is sucked in by the vacuum generated by the original state. The material is discharged from the tube under the mechanical pressure of the pressure roller, and so on. , So as to achieve the purpose of continuous output of materials.